With the FLOWSIC100 EX-Z2-PN16 / CL150 gas flow measurement devices measurements can be carried out at pressures up to 16 bar - also in hazardous areas Zone 2. The ultrasonic transducers have a high acoustic power and are suitable for measurements in large duct diameters up to 1700 mm or for difficult gas compositions. The sender/receiver units are available as hermetically sealed versions made of stainless steel or titanium.
The standard system contains a MCU control unit and 2 sender/receiver units. The MCU is used for input and output of signals, for calculation of reference values (standardization) or mass flows, as well as user-friendly LCD interface.
At a glance
| Corrosion-resistant transducers made of stainless steel or titanium |
| Explosion-proof version for applications in Zone 2 (ATEX) |
| Process pressure up to 16 bar |
| Hermetically sealed ultrasonic transducers |
| Integral measurement over the duct diameter |
| Automatic function control with zero and span point check |
Your benefits
| Reliable and accurate measurement also at low gas velocities |
| No movable parts, therefore low maintenance |
| Measurement independent of pressure, temperature and gas composition |
| Approved for usage in hazardous areas Zone 2 (ATEX) |
| Representative measuring results due to measurement across the whole duct diameter |
| No influence on the gas flow due to contact-free measurement |
| User-friendly operation and device diagnosis via MCU control unit and SOPAS ET operating software |
Fields of application
| Natural gas industry |
| Chemical and plastics manufacturing industry |
| Petrochemical industry and refineries |
| Cement manufacturing |
| Iron and steel production |
| Pharmaceutical industry |
| Glass industry |
| Food industry |
| Technical data | |||
| Measurement principle: | Ultrasonic transit time difference measurement | ||
| Measured values: | Gas velocity Gas temperature Mass flow Sound velocity Volumetric flow, a. c. Volumetric flow s. c. |
||
| Max. number of measurands: | 1 | ||
| Measuring ranges: | Gas velocity: -40 ... 0 m/s / 0 ... 40 m/s | ||
| Comment: | Continuously adjustable | ||
| Температура процесса: | -40 ... +260 °C versions for lower temperatures on request |
||
| Давление процесса: | -0.5 ... 16 bar | ||
| Dust load: | ≤1 g/m3 | ||
| Nominal pipe size: | 0.15 ... 1.7 m | ||
| Length of measuring path: | 0.2 ... 2 m larger measuring distances on request |
||
| Ambient temperature: | FLSE100 sender/receiver units, MCUP control unit: -40 ... +60 °C | ||
| Ex-approvals ATEX: | FLSE100 sender/receiver units: II 3 G EEx nA II T4 certified by manufacturer MCUP control unit: II 3 G EEx nA II T4 Ex-version optional; certified by manufacturer |
||
| Electrical safety: | CE | ||
| Enclosure rating: | IP 65 | ||
| Analog outputs: | 1 output: 0/2/4 ... 22 mA, 750 Ω additional outputs if using I/O modules |
||
| Analog inputs: | 2 inputs: 0 ... 20 mA , 0 ... 10 V additional inputs if using I/O modules |
||
| Digital outputs: | 5 floating outputs (change-over contacts) 48 V, 1 A additional outputs if using I/O modules |
||
| Digital inputs: | 4 potential-free contacts additional inputs if using I/O modules |
||
| Interfaces: | Ethernet (option) RS-232 (service interface) RS-485 (option) USB 1.1 |
||
| Bus protocol: | Ethernet TCP/IP (option) Modbus (option) PROFIBUS DP (option) |
||
| Operation: | Via LC-display or software SOPAS ET | ||
| Device version: | Cross-duct version | ||
| System components: | Connection unit Flange(s) with tube FLSE100 sender/receiver units MCUP control unit |
||
| Diagnostics functions: | Automatic check cycle for zero and span point Extended device diagnosis via SOPAS ET software |
||
| Mounting: | Installation angle 60°, Flange DIN PN16 or ANSI CL150 | ||
With the FLOWSIC100 EX-Z2-PN16 / CL150 gas flow measuring devices measurements can be carried out at pressures up to 16 bar - also in hazardous areas Zone 2. The ultrasonic transducers have a high acoustic power and are suitable for measurements in large duct diameters up to 1700 mm or for difficult gas compositions. The sender/receiver units are available as hermetically sealed versions made of stainless steel or titanium. A retraction mechanism allows removal of the sender/receiver units during plant operation.
The standard system contains a MCU control unit and 2 sender/receiver units. The MCU is used for input and output of signals, for calculation of reference values (standardization) or mass flows, as well as user-friendly LCD interface.
At a glance
| Corrosion-resistant transducers made of stainless steel or titanium |
| Explosion-proof version for applications in Zone 2 (ATEX) |
| Sender/receiver units with retraction mechanism |
| Process pressure up to 16 bar |
| Hermetically sealed ultrasonic transducers |
| Integral measurement over the duct diameter |
| Automatic function control with zero and span point check |
Your benefits
| Reliable and accurate measurement also at low gas velocities |
| No movable parts, therefore low maintenance |
| Measurement independent of pressure, temperature and gas composition |
| Approved for usage in hazardous areas Zone 2 (ATEX) |
| Exchange of sender/receiver units during plant operation |
| Representative measuring results due to measurement across the whole duct diameter |
| No influence on the gas flow due to contact-free measurement |
| User-friendly operation and device diagnosis via MCU control unit and SOPAS ET operating software |
Fields of application
| Natural gas industry |
| Chemical and plastics manufacturing industry |
| Petrochemical industry and refineries |
| Cement manufacturing |
| Iron and steel production |
| Pharmaceutical industry |
| Glass industry |
| Food industry |
| Technical data | |||
| Measurement principle: | Ultrasonic transit time difference measurement | ||
| Measured values: | Gas velocity Gas temperature Mass flow Sound velocity Volumetric flow, a. c. Volumetric flow s. c. |
||
| Max. number of measurands: | 1 | ||
| Measuring ranges: | Gas velocity: -40 ... 0 m/s / 0 ... 40 m/s | ||
| Comment: | Continuously adjustable | ||
| Температура процесса: | -40 ... +260 °C versions for lower temperatures on request |
||
| Давление процесса: | -0.5 ... 16 bar | ||
| Dust load: | ≤1 g/m3 | ||
| Nominal pipe size: | 0.15 ... 1.7 m | ||
| Length of measuring path: | 0.2 ... 2 m larger measuring distances on request |
||
| Ambient temperature: | FLSE100 sender/receiver units, MCUP control unit: -40 ... +60 °C | ||
| Ex-approvals ATEX: | FLSE100 sender/receiver units: II 3 G EEx nA II T4 certified by manufacturer MCUP control unit: II 3 G EEx nA IIC T4 Ex-version optional; certified by manufacturer |
||
| Electrical safety: | CE | ||
| Enclosure rating: | IP 65 | ||
| Analog outputs: | 1 output: 0/2/4 ... 22 mA, 750 Ω additional outputs if using I/O modules |
||
| Analog inputs: | 2 inputs: 0 ... 20 mA , 0 ... 10 V additional inputs if using I/O modules |
||
| Digital outputs: | 5 floating outputs (change-over contacts) 48 V, 1 A additional outputs if using I/O modules |
||
| Digital inputs: | 4 potential-free contacts additional inputs if using I/O modules |
||
| Interfaces: | Ethernet (option) RS-232 (service interface) RS-485 (option) USB 1.1 |
||
| Bus protocol: | Ethernet TCP/IP (option) Modbus (option) PROFIBUS DP (option) |
||
| Operation: | Via LC-display or software SOPAS ET | ||
| Device version: | Cross-duct version | ||
| System components: | Connection unit Flange with retraction mechanism FLSE100 sender/receiver units MCUP control unit |
||
| Diagnostics functions: | Automatic check cycle for zero and span point Extended device diagnosis via SOPAS ET software |
||
| Mounting: | Installation angle 60°, Flange DIN PN16 or ANSI CL150 | ||
With the FLOWSIC100 PN16 / CL150 gas flow measuring devices measurements can be carried out at pressures up to 16 bar. The ultrasonic transducers have a high acoustic power and are suited for transmitting measurements in large duct diameters up to 1700 mm or for difficult gas compositions. The sender/receiver units are available as hermetically sealed versions made of stainless steel or titanium. The standard system contains a control unit MCU and 2 sender/receiver units. The MCU is used for input and output of signals, for calculation of reference values (standardization) or mass flows, as well as user-friendly LCD interface.
At a glance
| Corrosion-resistant transducers made of stainless steel or titanium |
| Process pressure up to 16 bar |
| Hermetically sealed ultrasonic transducers |
| Integral measurement over the duct diameter |
| Measurement without pressure loss, therefore no influences on the process |
| Automatic function control with zero and span point check |
Your benefits
| Reliable and accurate measurement also at low gas velocities |
| No movable parts, therefore low maintenance |
| Measurement independent of pressure, temperature and gas composition |
| Representative measuring results due to measurement across the whole duct diameter |
| No influence on the gas flow due to contact-free measurement |
| User-friendly operation and device diagnosis via MCU control unit and SOPAS ET operating software |
Fields of application
| Natural gas industry |
| Chemical and plastics manufacturing industry |
| Petrochemical industry and refineries |
| Cement manufacturing |
| Steel and iron production |
| Pharmaceutical industry |
| Glass industry |
| Food industry |
| Technical data | |||
| Measurement principle: | Ultrasonic transit time difference measurement | ||
| Measured values: | Gas velocity Gas temperature Mass flow Sound velocity Volumetric flow, a. c. Volumetric flow s. c. |
||
| Max. number of measurands: | 1 | ||
| Measuring ranges: | Gas velocity: -40 ... 0 m/s / 0 ... 40 m/s | ||
| Comment: | Continuously adjustable | ||
| Температура процесса: | -40 ... +260 °C versions for lower temperatures on request |
||
| Давление процесса: | -0.5 ... 16 bar | ||
| Dust load: | ≤1 g/m3 | ||
| Nominal pipe size: | 0.15 ... 1.7 m | ||
| Length of measuring path: | 0.2 ... 2 m larger measuring distances on request |
||
| Ambient temperature: | FLSE100 sender/receiver units, MCUP control unit: -40 ... +60 °C | ||
| Electrical safety: | CE | ||
| Enclosure rating: | IP 65 | ||
| Analog outputs: | 1 output: 0/2/4 ... 22 mA, 750 Ω additional outputs if using I/O modules |
||
| Analog inputs: | 2 inputs: 0 ... 20 mA , 0 ... 10 V additional inputs if using I/O modules |
||
| Digital outputs: | 5 floating outputs (change-over contacts) 48 V, 1 A additional outputs if using I/O modules |
||
| Digital inputs: | 4 potential-free contacts additional inputs if using I/O modules |
||
| Interfaces: | Ethernet (option) RS-232 (service interface) RS-485 (option) USB 1.1 |
||
| Bus protocol: | Ethernet TCP/IP (option) Modbus (option) PROFIBUS DP (option) |
||
| Operation: | Via LC-display or software SOPAS ET | ||
| Device version: | Cross-duct version | ||
| System components: | Connection unit Flange(s) with tube FLSE100 sender/receiver units MCUP control unit |
||
| Mounting: | Installation angle 60°, Flange DIN PN16 or ANSI CL150 | ||
The ultrasonic transducers of the FLOWSIC100 PR-EX-Z2 gas flow measuring device are mounted on one measuring probe. Therefore installation is on only one side of the duct. The rugged titanium transducers stand for high durability. The standard version contains the measuring probe in an explosion-proof version for hazardous areas Zone 2 and an MCU control unit. The MCU is used for input and output of signals, for calculation of reference values (standardization) or mass flows, as well as user-friendly LCD interface.
At a glance
| Corrosion-resistant transducers made of titanium |
| Measuring probe version for installation from one side |
| Explosion-proof for application in Zone 2 (ATEX) |
| Automatic function control with zero and span point check |
Your benefits
| Installation from only one side of the duct |
| No moving parts, therefore low maintenance effort |
| Measurement independent from pressure, temperature and gas composition |
| High durability due to robust transducers |
| User-friendly operation and device diagnosis via MCU control unit and SOPAS ET operating software |
Fields of application
| Natural gas industry |
| Chemical and plastics manufacturing industry |
| Petrochemical industry and refineries |
| Iron and steel production |
| Pharmaceutical industry |
| Glass industry |
| Food industry |
| Technical data | |||
| Measurement principle: | Ultrasonic transit time difference measurement | ||
| Measured values: | Gas velocity Gas temperature Mass flow Sound velocity Volumetric flow, a. c. Volumetric flow s. c. |
||
| Max. number of measurands: | 1 | ||
| Measuring ranges: | Gas velocity: -40 ... 0 m/s / 0 ... 40 m/s | ||
| Comment: | Continuously adjustable | ||
| Температура процесса: | -40 ... +260 °C versions for lower temperatures on request |
||
| Давление процесса: | -100 ... 100 hPa | ||
| Dust load: | ≤1 g/m3 | ||
| Nominal pipe size: | ≥0.4 m | ||
| Length of measuring path: | 0.27 ... 0.28 m | ||
| Ambient temperature: | FLSE100 sender/receiver units, MCUP control unit: -40 ... +60 °C | ||
| Ex-approvals ATEX: | FLSE100 sender/receiver units: II 3 G EEx nA II T4 certified by manufacturer MCUP control unit: II 3 G EEx nA II T4 Ex-version optional; certified by manufacturer |
||
| Electrical safety: | CE | ||
| Enclosure rating: | IP 65 | ||
| Analog outputs: | 1 output: 0/2/4 ... 22 mA, 750 Ω additional outputs if using I/O modules |
||
| Analog inputs: | 2 inputs: 0 ... 20 mA , 0 ... 10 V additional inputs if using I/O modules |
||
| Digital outputs: | 5 floating outputs (change-over contacts) 48 V, 1 A additional outputs if using I/O modules |
||
| Digital inputs: | 4 potential-free contacts additional inputs if using I/O modules |
||
| Interfaces: | Ethernet (option) RS-232 (service interface) RS-485 (option) USB 1.1 |
||
| Bus protocol: | Ethernet TCP/IP (option) Modbus (option) PROFIBUS DP (option) |
||
| Operation: | Via LC-display or software SOPAS ET | ||
| Device version: | Measuring probe version | ||
| System components: | Connection unit Flange(s) with tube FLSE100 sender/receiver units MCUP control unit |
||
| Diagnostics functions: | Automatic check cycle for zero and span point Extended device diagnosis via SOPAS ET software |
||
| Mounting: | Installation angle 45° | ||
With the FLOWSIC100 Process gas flow measurement devices measurements can be carried out at pressures up to 16 bar - also in hazardous areas Zone 2. The sender/receiver units are available as hermetically sealed versions made of stainless steel or titanium. The standard system contains a MCU control unit and 2 sender/receiver units or a measuring probe. The MCU is used for input and output of signals, for calculation of reference values (standardization) or mass flows, as well as user-friendly LCD interface.
At a glance
| Corrosion-resistant transducers made of stainless steel or titanium |
| Process pressure up to 16 bar |
| Explosion-proof version for applications in Zone 2 (ATEX) available |
| Hermetically sealed ultrasonic transducers |
| Measurement without pressure loss, therefore no influences on the process |
| Automatic function control with zero and span point check |
Your benefits
| Reliable and accurate measurement also at low gas velocities |
| No movable parts, therefore low maintenance |
| Measurement independent of pressure, temperature and gas composition |
| No influence on the gas flow due to contact-free measurement |
| Approved for usage in hazardous areas Zone 2 (ATEX) |
| User-friendly operation and device diagnosis via MCU control unit and SOPAS ET operating software |
Fields of application
| Natural gas industry |
| Chemical and plastics manufacturing industry |
| Petrochemical industry and refineries |
| Cement manufacturing |
| Steel and iron production |
| Pharmaceutical industry |
| Glass industry |
| Food industry |
| Technical data | |||
| Max. number of measurands: | 1 | ||
| Measured values: | Gas velocity, Gas temperature, Mass flow, Sound velocity, Volumetric flow, a. c., Volumetric flow s. c. | ||
| Measurement principle: | Ultrasonic transit time difference measurement | ||
| Measuring ranges: | Gas velocity: 0 ... ± 40 m/s | ||
| Diagnostics functions: | Automatic check cycle for zero and span point Extended device diagnosis via SOPAS ET software |
||
| Температура процесса: | -40 ... +260 °C | ||
| Давление процесса: | -0.5 ... 16 bar depending on device version |
||
| Nominal pipe size: | 0.15 ... 1.7 m depending on device version |
||
| Dust load: | ≤1 g/m3 | ||
| Ambient temperature: | FLSE100 sender/receiver units, MCUP control unit: -40 ... +60 °C | ||
| Ex-approvals ATEX: | FLSE100 sender/receiver units: II 3 G Ex nA II T4 Gc MCUP control unit: II 3 G EEx nA II T4 Ex-version optional |
||
| Electrical safety: | CE | ||
| Enclosure rating: | IP 65 | ||
| Analog outputs: | 1 output: 0/2/4 ... 20 mA, 750 Ω electrically isolated; up to five outputs when using additional modules (option) |
||
| Analog inputs: | 2 inputs: 0 ... 20 mA up to four outputs when using additional modules (option) |
||
| Digital outputs: | 5 relay outputs (change-over contacts), potential-free: 48 V, 1 A safety extra-low voltage; for status signals "operation/malfunction", "limit value", "warning", "maintenance" and "check cycle" |
||
| Digital inputs: | 4 potential-free contacts |
||
| Interfaces: | RS-232 (via clamp terminal; service interface) RS-485 (for connection of sender/receiver unit(s)) USB 1.1 (virtual COM port; service interface) |
||
| Bus protocol: | Ethernet TCP/IP (via optional interface module) Modbus (via optional interface module) Modbus TCP (via optional interface module) PROFIBUS DP (via optional interface module) |
||
| Operation: | Via LC-display or software SOPAS ET | ||
| Device version: | Cross-duct version Measuring probe version |
||
| System components: | Connection unit Flange(s) with tube FLSE100 sender/receiver units MCUP control unit |
||
| Mounting: | Installation angle 45° (probe version) Installation angle 60° Flange DIN PN16 or ANSI CL150 |
||