+7 (812) 432-38-38
+7 (812) 432-36-36
Пн-Пт 9:00 — 18:00
 
Заказать оборудование
 

SEK37

 
 
Арт. 1037376

At a glance

  • Motor feedback systems for the basic performance range
  • 16 sine/cosine periods per revolution
  • Absolute position with a resolution of 512 increments per revolution and 4,096 revolutions with the multiturn system
  • Programming of the position value
  • Electronic type label
  • HIPERFACE® interface
  • Installed version with tapered shaft and axial or radial connector outlet
  • Conforms to RoHs

    Your benefits

  • The small dimension allows manufacturers of low-power and minimal-power motors to considerably reduce the size of their motors
  • The SEK/SEL37 motor feedback systems are excellently suited for use under rough environmental conditions
  • The capacitive principle of measurement with holistic scanning allows for high axial and radial tolerances
  • The consistent mechanical components in SKS/SKM36 allow for a high degree of flexibility with various encoder systems
    Performance
    Number of sine/cosine periods per revolution: 16
    Number of the absolute ascertainable revolutions: 1 (Singleturn)
    Total number of steps: 512
    Шаг измерения: 20 angular seconds (at interpolation of the sine/cosine signals with e.g. 12 Bit)
    Integral non-linearity typ.: ± 288 angular seconds (Error limits for evaluating sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Differential non-linearity: ± 144 angular seconds (Non-linearity within a sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Operating speed: 6,000 /min, up to which the absolute position can be reliably produced
    Available memory area: 1,792 Byte (EEPROM 2048) 1)
    Maximum number of steps per revolution: 512 Via RS485
    Mechanical data
    Dimensions: See dimensional drawing
    Масса: 0.05 kg
    Moment of inertia of the rotor: 1 gcm²
    Maximum operating speed: 12,000 /min
    Maximum angular acceleration: 500,000 rad/s²
    Тип подключения: Connector, 8-pin, axial
    Permissible axial shaft movement: ± 0.3 mm
    Shaft version: Tapered shaft
    Permissible radial shaft movement: ± 0.15 mm
    Electrical data
    Electrical interface: HIPERFACE
    Operating voltage range/supply Voltage: 7 V DC ... 12 V DC
    Recommended supply voltage: 8 V DC
    Operating current: 1)
    Interfaces
    Type of code for the absolute value: Binary
    Кодовая последовательность: Increasing, for clockwise shaft rotation, looking in direction "A" (see dimensional drawing)
    Interface signals: Process data channel SIN, REFSIN, COS, REFCOS: analog, differential
    parameter channel RS 485: digital
    Данные окуражающей среды
    Working temperature range: -40 °C ... 115 °C
    Storage temperature range: -50 °C ... 125 °C, without package
    Относительная влажность / конденсат: 90 %, Condensation not permitted
    Устойчивость к ударам: 100 g, 10 ms (according to EN 60068-2-27)
    Resistance to vibration: 50 g, 10 Hz ... 2,000 Hz (according to EN 60068-2-6)
    EMC: According to EN 61000-6-2 and EN 61000-6-3 1)
    Enclosure rating: IP 40, according to IEC 60529, built-on version, with mating connector inserted and closed cover
     
    Арт. 1037378

    At a glance

  • Motor feedback systems for the basic performance range
  • 16 sine/cosine periods per revolution
  • Absolute position with a resolution of 512 increments per revolution and 4,096 revolutions with the multiturn system
  • Programming of the position value
  • Electronic type label
  • HIPERFACE® interface
  • Installed version with tapered shaft and axial or radial connector outlet
  • Conforms to RoHs

    Your benefits

  • The small dimension allows manufacturers of low-power and minimal-power motors to considerably reduce the size of their motors
  • The SEK/SEL37 motor feedback systems are excellently suited for use under rough environmental conditions
  • The capacitive principle of measurement with holistic scanning allows for high axial and radial tolerances
  • The consistent mechanical components in SKS/SKM36 allow for a high degree of flexibility with various encoder systems
    Performance
    Number of sine/cosine periods per revolution: 16
    Number of the absolute ascertainable revolutions: 1 (Singleturn)
    Total number of steps: 512
    Шаг измерения: 20 angular seconds (at interpolation of the sine/cosine signals with e.g. 12 Bit)
    Integral non-linearity typ.: ± 288 angular seconds (Error limits for evaluating sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Differential non-linearity: ± 144 angular seconds (Non-linearity within a sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Operating speed: 6,000 /min, up to which the absolute position can be reliably produced
    Available memory area: 1,792 Byte (EEPROM 2048) 1)
    Maximum number of steps per revolution: 512 Via RS485
    Mechanical data
    Dimensions: See dimensional drawing
    Масса: 0.04 kg
    Moment of inertia of the rotor: 1 gcm²
    Maximum operating speed: 12,000 /min
    Maximum angular acceleration: 500,000 rad/s²
    Тип подключения: Connector, 8-pin, radial
    Permissible axial shaft movement: ± 0.3 mm
    Shaft version: Tapered shaft
    Permissible radial shaft movement: ± 0.15 mm
    Electrical data
    Electrical interface: HIPERFACE
    Operating voltage range/supply Voltage: 7 V DC ... 12 V DC
    Recommended supply voltage: 8 V DC
    Operating current: 1)
    Interfaces
    Type of code for the absolute value: Binary
    Кодовая последовательность: Increasing, for clockwise shaft rotation, looking in direction "A" (see dimensional drawing)
    Interface signals: Process data channel SIN, REFSIN, COS, REFCOS: analog, differential
    parameter channel RS 485: digital
    Данные окуражающей среды
    Working temperature range: -40 °C ... 115 °C
    Storage temperature range: -50 °C ... 125 °C, without package
    Относительная влажность / конденсат: 90 %, Condensation not permitted
    Устойчивость к ударам: 100 g, 10 ms (according to EN 60068-2-27)
    Resistance to vibration: 50 g, 10 Hz ... 2,000 Hz (according to EN 60068-2-6)
    EMC: According to EN 61000-6-2 and EN 61000-6-3 1)
    Enclosure rating: IP 20, according to IEC 60529, built-on version, with mating connector inserted and closed cover
     
    Арт. 1037377

    At a glance

  • Motor feedback systems for the basic performance range
  • 16 sine/cosine periods per revolution
  • Absolute position with a resolution of 512 increments per revolution and 4,096 revolutions with the multiturn system
  • Programming of the position value
  • Electronic type label
  • HIPERFACE® interface
  • Installed version with tapered shaft and axial or radial connector outlet
  • Conforms to RoHs

    Your benefits

  • The small dimension allows manufacturers of low-power and minimal-power motors to considerably reduce the size of their motors
  • The SEK/SEL37 motor feedback systems are excellently suited for use under rough environmental conditions
  • The capacitive principle of measurement with holistic scanning allows for high axial and radial tolerances
  • The consistent mechanical components in SKS/SKM36 allow for a high degree of flexibility with various encoder systems
    Performance
    Number of sine/cosine periods per revolution: 16
    Number of the absolute ascertainable revolutions: 4,096 (Multiturn)
    Total number of steps: 2,097,152
    Шаг измерения: 20 angular seconds (at interpolation of the sine/cosine signals with e.g. 12 Bit)
    Integral non-linearity typ.: ± 288 angular seconds (Error limits for evaluating sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Differential non-linearity: ± 144 angular seconds (Non-linearity within a sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Operating speed: 6,000 /min, up to which the absolute position can be reliably produced
    Available memory area: 1,792 Byte (EEPROM 2048) 1)
    Maximum number of steps per revolution: 512 Via RS485
    Mechanical data
    Dimensions: See dimensional drawing
    Масса: 0.05 kg
    Moment of inertia of the rotor: 1 gcm²
    Maximum operating speed: 12,000 /min
    Maximum angular acceleration: 500,000 rad/s²
    Тип подключения: Connector, 8-pin, axial
    Permissible axial shaft movement: ± 0.3 mm
    Shaft version: Tapered shaft
    Permissible radial shaft movement: ± 0.15 mm
    Electrical data
    Electrical interface: HIPERFACE
    Operating voltage range/supply Voltage: 7 V DC ... 12 V DC
    Recommended supply voltage: 8 V DC
    Operating current: 1)
    Interfaces
    Type of code for the absolute value: Binary
    Кодовая последовательность: Increasing, for clockwise shaft rotation, looking in direction "A" (see dimensional drawing)
    Interface signals: Process data channel SIN, REFSIN, COS, REFCOS: analog, differential
    parameter channel RS 485: digital
    Данные окуражающей среды
    Working temperature range: -20 °C ... 115 °C
    Storage temperature range: -50 °C ... 125 °C, without package
    Относительная влажность / конденсат: 90 %, Condensation not permitted
    Устойчивость к ударам: 100 g, 10 ms (according to EN 60068-2-27)
    Resistance to vibration: 50 g, 10 Hz ... 2,000 Hz (according to EN 60068-2-6)
    EMC: According to EN 61000-6-2 and EN 61000-6-3 1)
    Enclosure rating: IP 40, according to IEC 60529, built-on version, with mating connector inserted and closed cover
     
    Арт. 1037379

    At a glance

  • Motor feedback systems for the basic performance range
  • 16 sine/cosine periods per revolution
  • Absolute position with a resolution of 512 increments per revolution and 4,096 revolutions with the multiturn system
  • Programming of the position value
  • Electronic type label
  • HIPERFACE® interface
  • Installed version with tapered shaft and axial or radial connector outlet
  • Conforms to RoHs

    Your benefits

  • The small dimension allows manufacturers of low-power and minimal-power motors to considerably reduce the size of their motors
  • The SEK/SEL37 motor feedback systems are excellently suited for use under rough environmental conditions
  • The capacitive principle of measurement with holistic scanning allows for high axial and radial tolerances
  • The consistent mechanical components in SKS/SKM36 allow for a high degree of flexibility with various encoder systems
    Performance
    Number of sine/cosine periods per revolution: 16
    Number of the absolute ascertainable revolutions: 4,096 (Multiturn)
    Total number of steps: 2,097,152
    Шаг измерения: 20 angular seconds (at interpolation of the sine/cosine signals with e.g. 12 Bit)
    Integral non-linearity typ.: ± 288 angular seconds (Error limits for evaluating sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Differential non-linearity: ± 144 angular seconds (Non-linearity within a sine/cosine period)
    typical values at nominal position ± 0,1 mm and + 20 °C
    Operating speed: 6,000 /min, up to which the absolute position can be reliably produced
    Available memory area: 1,792 Byte (EEPROM 2048) 1)
    Maximum number of steps per revolution: 512 Via RS485
    Mechanical data
    Dimensions: See dimensional drawing
    Масса: 0.04 kg
    Moment of inertia of the rotor: 1 gcm²
    Maximum operating speed: 12,000 /min
    Maximum angular acceleration: 500,000 rad/s²
    Тип подключения: Connector, 8-pin, radial
    Permissible axial shaft movement: ± 0.3 mm
    Shaft version: Tapered shaft
    Permissible radial shaft movement: ± 0.15 mm
    Electrical data
    Electrical interface: HIPERFACE
    Operating voltage range/supply Voltage: 7 V DC ... 12 V DC
    Recommended supply voltage: 8 V DC
    Operating current: 1)
    Interfaces
    Type of code for the absolute value: Binary
    Кодовая последовательность: Increasing, for clockwise shaft rotation, looking in direction "A" (see dimensional drawing)
    Interface signals: Process data channel SIN, REFSIN, COS, REFCOS: analog, differential
    parameter channel RS 485: digital
    Данные окуражающей среды
    Working temperature range: -20 °C ... 115 °C
    Storage temperature range: -50 °C ... 125 °C, without package
    Относительная влажность / конденсат: 90 %, Condensation not permitted
    Устойчивость к ударам: 100 g, 10 ms (according to EN 60068-2-27)
    Resistance to vibration: 50 g, 10 Hz ... 2,000 Hz (according to EN 60068-2-6)
    EMC: According to EN 61000-6-2 and EN 61000-6-3 1)
    Enclosure rating: IP 20, according to IEC 60529, built-on version, with mating connector inserted and closed cover
     
     

     
     
     
    Имя Отчество:
     
    Адрес электронной почты:
     
    Контактный телефон:
     
    Наименование компании:
     
    Содержание заказа: