At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | G ½ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | G ½ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 15 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.9 l/min | ||
Maximum flow: | 36 l/min | ||
Inlet zone: | 30 cm | ||
Зона выпуска | 5 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.006 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 350 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 15 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.9 l/min | ||
Maximum flow: | 36 l/min | ||
Inlet zone: | 30 cm | ||
Зона выпуска | 5 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.006 l/min |
Mechanical data | |||
Process connection: | G ¾ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 350 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 15 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.9 l/min | ||
Maximum flow: | 36 l/min | ||
Inlet zone: | 30 cm | ||
Зона выпуска | 5 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.006 l/min |
Mechanical data | |||
Process connection: | G ¾ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 350 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 20 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 3.5 l/min | ||
Maximum flow: | 60 l/min | ||
Inlet zone: | 50 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.012 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 420 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 20 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 3.5 l/min | ||
Maximum flow: | 60 l/min | ||
Inlet zone: | 50 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.012 l/min |
Mechanical data | |||
Process connection: | G 1 | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 420 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 20 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 3.5 l/min | ||
Maximum flow: | 60 l/min | ||
Inlet zone: | 50 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.012 l/min |
Mechanical data | |||
Process connection: | G 1 | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 420 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | G 1 ¼ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 1 % (of reading +/- 3 mm/s (with calibration report)) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | G 1 ¼ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | G ½ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | G ½ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | ½'' NPT | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 10 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.3 l/min | ||
Maximum flow: | 21 l/min | ||
Inlet zone: | 20 cm | ||
Зона выпуска | 0 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.003 l/min |
Mechanical data | |||
Process connection: | ½'' NPT | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 340 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 15 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.9 l/min | ||
Maximum flow: | 36 l/min | ||
Inlet zone: | 30 cm | ||
Зона выпуска | 5 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.006 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 350 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 15 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.9 l/min | ||
Maximum flow: | 36 l/min | ||
Inlet zone: | 30 cm | ||
Зона выпуска | 5 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.006 l/min |
Mechanical data | |||
Process connection: | G ¾ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 350 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 15 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.9 l/min | ||
Maximum flow: | 36 l/min | ||
Inlet zone: | 30 cm | ||
Зона выпуска | 5 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.006 l/min |
Mechanical data | |||
Process connection: | G ¾ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 350 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 15 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 16 bar |
Performance | |||
Minimim flow: | 0.9 l/min | ||
Maximum flow: | 36 l/min | ||
Inlet zone: | 30 cm | ||
Зона выпуска | 5 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.006 l/min |
Mechanical data | |||
Process connection: | ¾" NPT | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 350 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 20 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 3.5 l/min | ||
Maximum flow: | 60 l/min | ||
Inlet zone: | 50 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.012 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 420 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 20 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 3.5 l/min | ||
Maximum flow: | 60 l/min | ||
Inlet zone: | 50 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.012 l/min |
Mechanical data | |||
Process connection: | G 1 | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 420 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 20 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 3.5 l/min | ||
Maximum flow: | 60 l/min | ||
Inlet zone: | 50 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.012 l/min |
Mechanical data | |||
Process connection: | G 1 | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 420 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 20 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 3.5 l/min | ||
Maximum flow: | 60 l/min | ||
Inlet zone: | 50 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.012 l/min |
Mechanical data | |||
Process connection: | 1" NPT | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 420 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | Clamp (DIN 11864-3) | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | G 1 ¼ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | G 1 ¼ | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | 1 ¼" NPT | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 5-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 1 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring, dosing output, flow direction (depending on type) 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |
At a glance
Flow sensor for conductive and non-conductive liquids |
Compact design with no moving parts |
Process temperature up to 80 °C, process pressure up to 16 bar |
High chemical resistance due to seal-free sensor design |
Large display with membrane keyboard |
Integrated teaching tube detection |
Your benefits
Reduced maintenance costs |
Adjustable measuring ranges reduces the number of variants |
Ability to be used with conductive and non-conductive liquids reduces variants and lowers storage costs |
Straight measuring tube reduces pressure loss, thus reducing energy costs |
Sensor without seals increases process reliability and availability |
Flexible measurement system for all industries |
Features | |||
Средний: | Fluids | ||
Nominal width measuring tube: | NW 25 | ||
Температура процесса: | 0 °C ... +80 °C | ||
Давление процесса: | Max. 10 bar |
Performance | |||
Minimim flow: | 5 l/min | ||
Maximum flow: | 240 l/min | ||
Inlet zone: | 60 cm | ||
Зона выпуска | 10 cm | ||
Проводимость: | No limitation | ||
Accuracy of sensor element: | 2 % (of final value) 1) | ||
Повторяемость: | ≤ 0.5 % | ||
Resolution: | 0.03 l/min |
Mechanical data | |||
Process connection: | 1 ¼" NPT | ||
Детали, контактирующие с измеряемой средой: | PSU | ||
Материал корпуса: | PSU | ||
Вес: | 460 g | ||
Enclosure rating: | IP 67 |
Electrical data | |||
Supply voltage: | 18 V DC ... 30 V DC 1) | ||
Пульсации: | ≤ 5 Vpp 2) | ||
Потребляемая мощность: | ≤ 180 mA 3) | ||
Время инициализации: | ≤ 5 s | ||
Класс защиты: | III | ||
Тип подключения: | Round connector M12 x 1, 8-pin | ||
Output signal: | Analog output: 4 mA ... 20 mA, 0 mA ... 20 mA current flow and temperature 2 pulse/status output: transistor output for flow rate meter, empty pipe detection, flow monitoring 1 switching input for dosing and counter reset 4) |
||
Impuls/frequency output: | 0Â kHz ... 10 kHz | ||
Puls width: | ≤ 1 s | ||
Сигнал Высокого напряжения: | Vs - 2 V | ||
Signal voltage LOW: | ≤ 2 V | ||
Output current: | 5) | ||
Inductive load: | 1 H | ||
Capacitive load: | 100 nF | ||
Response time: | Filter off 100 ms, filter low 300 ms, filter medium 1 s, filter strong 4.2 s 6) | ||
Output load: | |||
Lower signal level: | 3.8 mA ... 4 mA | ||
Верхний уровень сигнала: | 20 mA ... 20.5 mA |
Данные окуражающей среды | |||
Ambient operating temperature: | 0 °C ... +60 °C | ||
Температура хранения: | -20 °C ... +70 °C |