+7 (812) 432-38-38
+7 (812) 432-36-36
Пн-Пт 9:00 — 18:00
 
Заказать оборудование
 

Scattered light dust measuring device, DUSTHUNTER SB30

Главная » Продукция » SICK » Анализаторы » Dust Measuring Devices » Scattered light dust measuring device, DUSTHUNTER SB30
 
 

The DUSTHUNTER SB30 is a measuring device for detecting low and medium dust concentrations, e.g., in hot or aggressive gases. The measurement is based on the proven measurement principle of backward light scattering. Installation is very easy from just one side of the duct. Two different penetration depths are available, enabling the measuring device to be adapted to highly diverse duct diameters.

At a glance

  • For low to medium dust content
  • Easy one-sided installation
  • Automatic check of zero and reference point
  • For medium to large duct diameters

    Your benefits

  • Easy installation, commissioning and operation
  • Proven measurement not dependent on gas velocity, humidity, or particle load
  • Cost-effective thanks to easy mounting from just one side; no alignment necessary
  • Self-monitoring for very low maintenance
  • Condition-based maintenance messages

    Fields of application

  • Emissions monitoring in industrial plants including, for example, power plants, heating systems, waste incineration plants, in steel production, and in cement plants
  • Monitoring of dust concentrations upstream of filter plants
  • Dust concentration measurements in flue gas ducts upstream and downstream of dust filters
    Technical data
    Measurement principles: Scattered light backward
    Measured values: Dust concentration (after gravimetric comparison measurement)
    Scattered light intensity
    Max. number of measurands: 1
    Measuring ranges: Scattered light intensity: 0 ... 30 SI / 0 ... 3,000 SI
    Comment: Measuring ranges freely selectable; three measuring ranges pre-configured (0 ... 30/500/3.000 SI)
    Gas flow rate: ≤20 m3/h
    Температура процесса: -40 ... +600 °C
    Давление процесса: With external purge air unit: -50 ... 30 hPa
    With control unit MCU-P: -50 ... 2 hPa
    Duct diameter: ≥500 mm
    Ambient temperature: Sender/receiver unit, control unit MCU-N: -40 ... +60 °C
    MCU-P control unit: -40 ... +45 °C
    intake temperatures for purge air
    Conformities: China's EPA compliant
    TUEV type-examination
    Electrical safety: CE
    Enclosure rating: IP 66
    Analog outputs: 1 output:
    0/2/4 ... 20 mA, 750 Ω
    electrically isolated; two additional outputs if using I/O modules (option)
    Analog inputs: 2 inputs:
    0 ... 20 mA
    not electrically isolated; two additional inputs if using I/O modules (option)
    Digital outputs: 5 relay contacts:
    48 V, 1 A
    potential-free; for status signals
    Digital inputs: 4 potential-free contacts
    Interfaces: RS-232 (service interface)
    RS-485 (via optional interface module)
    Interface module (option)
    USB (service interface)
    Bus protocol: Ethernet TCP/IP (via optional interface module)
    Modbus (via optional interface module)
    PROFIBUS DP (via optional interface module)
    Operation: Via LC-display (option) or software SOPAS ET
    Test functions: Automatic self-test (linearity, drift, aging)
    Manual linearity check with reference filter
    Options: External purge air unit, I/O module(s), Interface module(s), MCU control unit, SCU control unit
     
     

     
     
     
    Имя Отчество:
     
    Адрес электронной почты:
     
    Контактный телефон:
     
    Наименование компании:
     
    Содержание заказа: